Citroen Xantia

since 1993 of release

Repair and car operation



Citroen Xantia
+ Introduction
+ Operation manual
+ Routine maintenance
- Engine repair
   + the Repair procedures which are not demanding extraction of the engine from the car - petrol engines
   - The repair procedures which are not demanding extraction of the engine from the car - diesel engines
      Measurement of kompressionny pressure and engine check on tightness
      Fixing cranked / distributive shaft and TNVD for the purpose of prevention of casual hit of valves in contact to pistons in the course of performance of procedures of service of the car
      Removal and installation of a cover of a head of cylinders
      Removal and installation of a pulley of a cranked shaft
      Removal and installation of covers of a gas-distributing belt
      Belt of a drive of GRM - the general information, removal, check of a condition and installation
      Removal and installation of cogwheels of a belt of a drive of GRM
      Removal and installation of components of the right support of the power unit and natyazhitel of a gas-distributing belt
      Removal and installation of an intermediate roller of a gas-distributing belt
      Removal, check of a condition and installation of a camshaft and pushers of valves
      Check and adjustment of klapanny gaps
      Removal and installation of a head of cylinders
      Removal and installation of the pallet of a case
      Removal, check of a condition and installation of the oil pump with a driving chain
      Replacement of epiploons
      Sensors of level, pressure and temperature of impellent oil - the general information
      Removal, check of a condition and flywheel installation / driving disk
      Check of a condition and replacement of support of a suspension bracket of the power unit
      Removal and installation of a maslookhladitel
   + Removal and major maintenance of the engine
+ Systems of cooling, heating
+ Power supply system and release
+ engine Electric equipment
+ Coupling
+ Transmission
+ Power shafts
+ Uniform hydraulic system
+ Brake system
+ Running gear and steering
+ Body and salon furnish
+ Onboard electric equipment
+ electric equipment Schemes


ad6e8668

Replacement of epiploons

Right epiploon of a cranked shaft

 PERFORMANCE ORDER

1. Remove a cogwheel of a cranked shaft (see. Removal and installation of cogwheels of a belt of a drive of GRM).
2. Measure and write down landing depth of an epiploon.

3. By means of a suitable hook take an epiploon from the casing. Alternatively, drill or puncture in a face surface of an epiploon pair of openings, screw in them саморезы and take an epiploon, having grasped nippers heads of screws.

4. Clear a casing of an epiploon and carefully remove from walls of a nest and a shaft pin all roughnesses and the teases, capable to bring to failure of a new epiploon.
5. Grease sponges of a new epiploon with pure impellent oil, then accurately plant it on former depth in a nest in a casing (the opened end inside). As an opravka use a replaceable head of the corresponding size or a piece of a pipe of suitable diameter (the opravka should rest only against the firm external region of a face surface of an epiploon). For protection of an epiploon wind a pin of a cranked shaft with a thin adhesive tape and plant on it casing assembly with an epiploon.
6. Remove an adhesive tape.
7. Establish into place a cogwheel of a cranked shaft (see. Removal and installation of cogwheels of a belt of a drive of GRM).

Left epiploon of a cranked shaft

 PERFORMANCE ORDER

1. Remove a flywheel / a driving disk (see. Removal, check of a condition and flywheel installation / driving disk).
2. Execute the procedures described in subsection the Right epiploon of a cranked shaft, subitem 2 — 6 with that difference that this time the epiploon is put by external sponges outside. If sponges at installation of an epiploon are turned out, straighten them by means of a suitable hook. Try not to damage an epiploon.
3. Establish into place a flywheel / a driving disk (see. Sensors of level, pressure and temperature of impellent oil - the general information).

Right epiploon of a camshaft

 PERFORMANCE ORDER

1. Remove a camshaft cogwheel (see. Removal and installation of cogwheels of a belt of a drive of GRM). In effect, there is no need of complete removal of a gas-distributing belt, however it is worth to remember about high probability of pollution it oil.

2. Having hooked a suitable hook, take an epiploon from the casing. Alternatively, the epiploon can be taken with the help саморезов (see subsection the Right epiploon of a cranked shaft, item 3).

3. Carefully clear a casing of an epiploon and a surface of a pin of a camshaft.
4. Grease sponges of a new epiploon with pure impellent oil and plant it on a shaft pin (the opened end forward). For protection of sponges it is necessary to wind a pin with an adhesive tape previously.
5. By means of a suitable opravka press an epiploon in the casing aflush with a face surface of a head of cylinders. Use bolt М10 which should be screwed in a carving opening in a shaft end face, washers and a piece of a pipe suitable on diameter.
6. Establish into place a camshaft cogwheel (see. Removal and installation of cogwheels of a belt of a drive of GRM).
7. If removed, establish a gas-distributing belt (see. A belt of a drive of GRM - the general information, removal, check of a condition and installation).

 

Left epiploon of a camshaft

Consolidation of the left pin of a camshaft is made means of the sealing ring planted in a flange of a face plate. The epiploon is not provided. Replacement of a sealing ring is made by a plate otbolchivaniye from a head of cylinders.