Citroen Xantia

since 1993 of release

Repair and car operation



Citroen Xantia
+ Introduction
+ Operation manual
+ Routine maintenance
+ engine Repair
+ Systems of cooling, heating
- Power supply system and release
   + the Power supply system - petrol models
   + the Power supply system - diesel models
   - Systems of decrease in toxicity and production of the fulfilled gases
      Check of serviceability of a functioning / condition and replacement of components of systems of decrease in toxicity of the fulfilled gases
      The catalytic converter - the general information and precautionary measures
      System of production of the fulfilled gases - the general information, removal and installation
+ engine Electric equipment
+ Coupling
+ Transmission
+ Power shafts
+ Uniform hydraulic system
+ Brake system
+ Running gear and steering
+ Body and salon furnish
+ Onboard electric equipment
+ electric equipment Schemes


ad6e8668

Check of serviceability of a functioning / condition and replacement of components of systems of decrease in toxicity of the fulfilled gases

Petrol models

System of ventilation of a case

Components of system of ventilation do not need service, except for regular check of a condition of hoses.

System of catching of fuel evaporations

Check

 PERFORMANCE ORDER

1. Disconnect hoses from a coal adsorber and the valve of its purge and, by blowing off, make sure of their passableness. Defective adsorber and the valve of a purge are subject to replacement.

Replacement of a coal adsorber

 PERFORMANCE ORDER

1. The coal adsorber is behind a radiator and is fixed on the left wall of an impellent compartment.
2. Mark two hoses and disconnect them from the top part of an adsorber. If for fastening of hoses collars of braided type are used, at assembly it will be reasonable to replace them more practical screw or worm. If hoses fasten by means of sockets of fast undocking, wring out the central plugs of sockets a small screw-driver with a flat sting and remove step from unions.
3. Give fixing nuts and remove an adsorber from the basic arm. In case of need отболтите also remove an arm.
4. Installation is made upside-down. Track correctness of connection and reliability of fastening of hoses.

Replacement of the valve of a purge of an adsorber

 PERFORMANCE ORDER

1. The valve is fixed on the left wall of an impellent compartment, behind a coal adsorber.

2. Disconnect a negative wire from the battery. Release a clamp and disconnect electroconducting from the valve of a purge of an adsorber.

3. Disconnect hoses from both parties of the valve and liberate the last from the fixing collar. Take the purge valve from an impellent compartment.
4. Installation is made upside-down. Track correctness of an arrangement of the valve and reliability of fastening of hoses to it.

Catalytic converter and l-probe

Check

Efficiency of functioning of the catalytic converter can be checked only by a way of definition of composition of the fulfilled gases by means of carefully calibrated gas analyzer (address to Head Routine maintenance).

If contents level WITH on a cut of an exhaust pipe exceeds admissible value, the car should be driven away on car repair shop for carrying out complete diagnostics of systems of injection of fuel and ignition. If during such diagnostics any violation it is not possible to reveal, replace the catalytic converter (see. System of production of the fulfilled gases - the general information, removal and installation).

Replacement of the catalytic converter

See. System of production of the fulfilled gases - the general information, removal and installation.

L-probe replacement

The oxygen sensor is among fragile electronic elements. Do not shake a l-probe and do not drop it. Food or use break for cleaning of the sensor of chemical means also can lead to a l-probe exit out of operation.


 PERFORMANCE ORDER

1. Walk on electroconducting from the l-probe screwed in a reception pipe of system of production of fulfilled gases, to the top part of the case of transmission. Disunite both electric sockets and liberate electroconducting from intermediate clamps and bindings.
2. Turn out the sensor from a reception pipe. Also remove it together a sealing washer.
3. Installation is made upside-down. Do not forget to replace a sealing washer. Before installation grease a carving part of the sensor with high-temperature greasing. Track reliability of a tightening of the sensor and correctness of laying of its electroconducting (wires should not adjoin in the systems which was heated by surfaces of production of the fulfilled gases and the engine).

Diesel models

System of ventilation of a case

Components of system of ventilation do not need service, except for regular check of a condition of hoses.

Catalytic converter

Check

Efficiency of functioning of the catalytic converter can be checked only by a way of definition of composition of the fulfilled gases by means of carefully calibrated gas analyzer (address to Head Routine maintenance).

If there are doubts in serviceability of functioning of the catalytic converter, before make sure of serviceability of nozzles. More detailed information can be received at experts firm Citroёn company service centers.

Replacement

See. System of production of the fulfilled gases - the general information, removal and installation.

System of a retsirkulyatsiya of the fulfilled gases (EGR)

Check

It is necessary to charge performance of check of serviceability of functioning of EGR system to specialists of car repair shop.

Replacement of components

At the moment of drawing up of the real Management information on replacement of components of EGR system was absent.

System of compensation of changes of atmospheric pressure

Check

Also it is necessary to charge performance of check of serviceability of functioning of this system to specialists of car repair shop.

Replacement of components

Detailed information on replacement of the sensor of temperature of cooling liquid is provided in the Head of System of cooling, heating.

Information on replacement of the block of the relay/timer of system of preheat see in the section preheat System - diesel models.

At the moment of drawing up of the real Management information on replacement of the sensor switch of atmospheric pressure was absent.