Citroen Xantia

1. Prop up protivootkatny boots back wheels, then поддомкратьте a front of the car and establish it on props. Transfer the selector lever to situation N.
2. Remove the battery with the pallet and a basic plate (see. Head engine Electric equipment).
3. Remove the thermofilter (ы) systems of production of the fulfilled gases for the purpose of ensuring access to the basis of assembly of the lever of the selector of transfers (see. Head of the Power supply system and release). On some models it is necessary to remove also inlet air line (ы) (see. Head of the Power supply system and release).
4. Since the end of a driving cable turned to transmission turn out two screws of fastening of a cover of a cable to its basic arm. Accurately disconnect a cable tip from the spherical hinge of the lever of a choice of transfers.

Do not allow change of position of the lever of a choice after a detachment from it a driving cable! As an additional precautionary measure mark a starting position of the lever concerning a transmission case.

5. Moving back along a cable, liberate it from intermediate clamps. Try to remember a route of laying of a cable properly.
6. In salon of the car having accurately hooked, remove from the central console the panel of facing of the lever of the selector of transfers (address to Head the Body and salon furnish).
7. Turn out screws of fastening of the handle on a lever rod. Squeeze out a clamp rychazhok, turn the handle under 90 ° counter-clockwise, lift assembly up, then turn under 90 ° clockwise for the purpose of liberation of the button of a clamp from an executive rod of the lever. After removal of the handle take from it the clamp button with a spring.
8. Give four nuts of fastening of assembly of the lever to a floor.
9. Under the car disconnect lever assembly from the body panel and remove it from the car, remembering a route of laying of a cable.
10. Having laid lever assembly on a workbench, separate from the lever basis a protective cover and shift it along a cable.
11. Weaken a nut of fastening of a cover of a cable, then remove a fixing clamp. Having accurately hooked, disconnect a cable tip from the spherical hinge in the basis of the lever of the selector.
12. Attentively examine cable assembly on existence of signs of damage of a cover and a core wipe. Check serviceability of functioning of a cable: the core should move freely in a cover. Remember that after installation in regular situation, a cable functions with much bigger resistance. In case of identification of the slightest signs of malfunction replace assembly.

1. Slightly grease with greasing on the basis of a molybdenum disulfide open sites of the core of a cable, spherical hinges of levers and fixing mechanism of the lever.
2. Pass a cable in a casing of the lever of the selector. Track, the flange of a cover of a cable the openings got on reciprocal ledges of a casing. Fix a cable a clamp, track, that the external ends of the last correctly entered into gearing with reciprocal grooves in a lever casing while the internal ends appeared hooked for the casing basis. Tighten a fixing nut of a cover of a cable.
3. Strongly fix a core tip on the spherical hinge of the lever. Return to regular situation on the basis of the lever a protective cover.
4. Having tracked correctness of laying of a cable, get the lever from below on the regular place.
5. Involve lever assembly in salon and tighten four fixing nuts.
6. Establish in the lever handle the button and a clamp spring. Completely drown the button in the handle. Holding the button drowned, put on the handle a rod of the lever and, having slightly pressed, turn on 90 ° clockwise, then back for the purpose of input of the button of a clamp in gearing with an executive rod. Release the button, then screw and tighten four fixing screws.
7. Under the car, moving along a cable, fix it in all provided intermediate clamps and directing. Place an assembly bracket of a cover of a cable on a basic arm on AT case, screw and tighten fixing bolts.
8. Make sure that levers of the selector and a choice of transfers are in situation N, adjust a driving cable and connect it to the choice lever on transmission (see subitem 4 — 6 in the section Adjustment of a driving cable of a choice of transfers of AT).
9. Establish into place the thermofilter (ы) systems of production of the fulfilled gases (see. Head of the Power supply system and release), then lower the car on the earth.
10. Establish all other components acting in film for the purpose of ensuring access.