Citroen Xantia

since 1993 of release

Repair and car operation



Citroen Xantia
+ Introduction
+ Operation manual
+ Routine maintenance
+ engine Repair
+ Systems of cooling, heating
- Power supply system and release
   - Power supply system - petrol models
      Removal and installation of assembly of an air purifier
      Removal, installation and adjustment of a cable of gas
      Removal and installation of a pedal of gas
      Unleaded fuel - the general information and use rules
      Systems of injection of fuel - the general information
      Sbrasyvaniye of pressure in a power supply system
      Removal and installation of the fuel pump
      Removal and installation of the sensor of fuel consumption
      Removal and installation of a fuel tank
      Check of a condition and adjustment of system of injection of fuel
      Removal and installation of the case of a throttle
      Removal and installation of components of Bosch Motronic 5.1 system
      Removal and installation of components of Magneti-Marelli 8Р system
      Removal and installation of the inlet pipeline
      Removal and installation of a final collector
   + the Power supply system - diesel models
   + Systems of decrease in toxicity and production of the fulfilled gases
+ engine Electric equipment
+ Coupling
+ Transmission
+ Power shafts
+ Uniform hydraulic system
+ Brake system
+ Running gear and steering
+ Body and salon furnish
+ Onboard electric equipment
+ electric equipment Schemes


ad6e8668

Removal and installation of a fuel tank

Removal

 PERFORMANCE ORDER

1. Before removal the tank is necessary for devastating completely. As drain stopper it is not provided, to start removal of a tank best of all after all fuel will be developed. The remains can be pumped out through a jellied mouth manually (previously disconnect a negative wire from the battery).
2. To Poddomkratta a car back also establish it on props. Remove the right back wheel.
3. Remove intermediate section of system of production of the fulfilled gases with the exhaust silencer (see. Systems of decrease in toxicity and production of the fulfilled gases).
4. To Otboltita also remove from the car bottom the thermofilter.
5. To Otboltita bearing bracket of a fuel tank.
6. Take a lock finger and disconnect from driving draft from the back proof-reader of height of a road gleam. Take the proof-reader aside.
7. Without disconnecting, remove covers from the hydraulic tubes located under the bottom.
8. Liberate hydraulic tubes from clamps on the bottom of a fuel tank.
9. Liberate the fuel filter from the arm and take him aside.
10. Remove a mudguard of an arch of the right back wheel and disconnect from rubber tubes of the line of giving and fuel return.
11. Weaken collars and disconnect from a fuel tank a jellied mouth and ventilating hoses.
12. Get under a tank a telezhechny jack (for distribution of loading lay between a head of a jack and the tank bottom wooden whetstone). Cock a jack, having accepted on it fuel tank weight.
13. Turn out bolts of fastening of a tank and, having slightly handed over to the right, приопустите a tank on a jack.
14. Where it is required, disconnect electroconducting from an active hydraulic suspension bracket.
15. Wring out a plastic uvula and disconnect electroconducting from the fuel filter.
16. Release collars and disconnect hoses from assembly of a toplivozabornik.
17. Lower a fuel tank and take it from under the car.
18. If inside there are firm deposits or moisture, take from it gasoline pump assembly with a toplivozabornik and wash out a tank pure gasoline. The tank represents the integral tank made by a method of blowing of a synthetic material and in case of serious mechanical damage is subject to replacement. Nevertheless, in certain cases insignificant leaks can be eliminated with a way of performance of special repair procedures, - consult at specialists of car-care center.

Installation

Installation is made upside-down. The special attention should be turned for the next moments:
   a) At tank installation on the car track, that no hoses appeared clamped between a tank and the car bottom.
   b) Track correctness of laying and reliability of connection of all lines and hoses.
   c) Before connecting driving bent for to the proof-reader of height of a road gleam, transfer a control lever an active suspension bracket to the situation LOW.
   d) In summary fill in in a tank a small amount of pure fuel and check it on existence of signs of leaks, having driven away the car on a road roadside.