Citroen Xantia

since 1993 of release

Repair and car operation



Citroen Xantia
+ Introduction
+ Operation manual
+ Routine maintenance
+ engine Repair
+ Systems of cooling, heating
+ Power supply system and release
+ engine Electric equipment
+ Coupling
+ Transmission
+ Power shafts
+ Uniform hydraulic system
+ Brake system
+ Running gear and steering
+ Body and salon furnish
- Onboard electric equipment
   Search of causes of failures of electric equipment
   Safety locks and the relay - the general information
   Removal and installation of switches
   Replacement of lamps of external lighting and alarm devices
   Replacement of lamps of internal lighting devices
   Removal and installation of external lighting and alarm devices
   Adjustment of optical axes of head headlights
   Removal and installation of an instrument guard
   Removal and installation of components of an instrument guard
   Removal and installation of hours
   Removal and lighter installation
   Alarm system “do not forget to switch off lighting devices” - the general information
   Removal and installation of a horn of a horn
   Removal and installation of a driving cable of the speedometer/sensor of speed
   Removal and installation of the lever of a screen wiper
   Removal and installation of the electromotor and drafts of a drive of a cleaner of a windscreen
   Removal and installation of the electromotor of a drive of a back screen wiper
   Removal and installation of components of system of washing of glasses and lenses of head block headlights
   Removal and radio tape recorder installation
   Removal and installation of loudspeakers
   Removal and installation of the aerial of a radio receiver
   Anticreeping system - the general information
   Safety cushion - the general information, precautionary measures and system deactivation
   Removal and installation of components of a safety cushion
   Diagnostics of systems of electronic control
+ electric equipment Schemes


ad6e8668

Diagnostics of systems of electronic control


The scheme of connection of the button and, if necessary, a light-emitting diode to the 2-contact or 30-contact diagnostic socket

 

 

At emergence of malfunctions in system of ignition and supply of fuel on the dashboard загоается a control lamp. At the same time the monitor is switched to emergency operation and writes down malfunction. After an engine stop record of malfunction can be считана from memory of the device.

It is possible to poll memory of malfunction of a monitor by means of the OUT device of 304 097 T or by means of diagnostic station Citroёn 26A.

The device is connected to the diagnostic socket.

At each interruption of supply of a food on a monitor data from memory are erased!

The electronic anti-theft device again becomes more active.

Indication of a code of malfunction means that this malfunction was shown after the last cleaning of memory.

For elimination of malfunction check all constructive group.

At check of the fuel pump and the operating valve of idling indication malfunctions (codes 15 or 22) does not mean that all constructive group is faulty. In case of malfunction connections and conducting should be checked also.

Poll of memory of malfunctions by means of an auxiliary light-emitting diode

Reading of codes can be made both with use of the special scanner, and on a lamp of refusals on the dashboard or by means of a light-emitting diode.

 PERFORMANCE ORDER

1. Make button connection according to the scheme (see an illustration the Scheme of connection of the button and, if necessary, a light-emitting diode to the 2-contact or 30-contact diagnostic socket) to contact 2 two-contact or С2 the 30-contact socket (depending on model) and to the case. If on your model there is no control lamp of refusals, connect the light-emitting diode cathode to the diagnostic plug of the socket or the control unit according to the scheme (depending on model), and the light-emitting diode anode — to "+" - the battery plug.
2. Include ignition and leave included.
3. Press the button 5 seconds and release. The light-emitting diode or a lamp of refusals will give out a code 12 — the beginning of delivery of codes. Value of each category of a code corresponds to number of flashes by duration of 1 second. At first are transferred ten of code, then — units. Between categories — a pause in 1,5 seconds. After a pause of 2,5 seconds delivery of a code repeats.
For extraction of the following code again press the button and so before emergence of a code 11, обозначающегот the termination of a conclusion or lack of codes of malfunctions — if it appeared right after a code 12.
4. Disconnect wires and switch off ignition.
For removal of codes from memory of the block it is enough to press after delivery of a code 11 the button and to hold it during not less than 15 seconds, or it is simple to disconnect a negative cable from the storage battery not less than on 10 seconds.

Codes of malfunctions

Value

Code

End of delivery of codes

11

Beginning of delivery of codes

12

The sensor of temperature of soaked-up air

13

The sensor of temperature of cooling liquid of the engine

14

Supply voltage of the relay of the fuel pump

15

Management of the pump of cooling of a turbokompressor

18

Sensor of provision of a butterfly valve

21

Food of the valve of management by idling air

22

Valve of management of idling air

23

Electromagnet of the L management of air of the inlet pipeline

25

Electromagnet of the C management of air of the inlet pipeline

26

Sensor of speed of the car

27

Automatic control of a fuel mix (lambda probe)

31

Automatic control of a fuel mix (leaks, pressure in fuel system)

32

Measuring instrument of an air stream
The sensor of absolute pressure in the inlet pipeline
Sensor of extreme provision of a butterfly valve

33

Valve of a purge of a coal adsorber of system of catching паров fuels

34

Sensor switch of completely open provision of a butterfly valve

35

Relay of management of heating lambda probe

36

Sensor of turns of the engine

41

Valves of injectors

42

Management of an ignition advancing on a detonation

43

Sensor of a detonation 1

44

NV of a chain of the coil of ignition 1

45

Valve of regulation of pressure of pressurization of a turbokompressor

46

Regulation of pressure of pressurization of a turbokompressor

47

Warmed up a lambda probe 1

51

Management of structure of a mix And/supply voltage

52

Battery supply voltage

53

The control unit the engine / module of management of an ignition advancing on a detonation

54

Resistor of adjustment of CO

55

Immobilizator (anticreeping protection) engine

56

Coil of ignition 2

57

Coil of ignition 3

58

Coil of ignition 4

59

Valve of regulation of a turbokompressor

61

Sensor of a detonation 2

62

Warmed up a lambda probe 2

63

Management of mix structure In

64

Sensor of provision of a cam-shaft

65

Injector 1

71

Injector 2

72

Injector 3

73

Injector 4

74

Injector 5

75

Injector 6

76

The sensor of absolute pressure in the inlet pipeline

79

Management of injectors

91

Indication of activization of check of actuation mechanisms

Stand out in the course of check of the corresponding devices

Value

Code

Relay of the fuel pump

81

Injectors

82

Valve of management of idling air

83

Valve of a purge of a coal adsorber

84

Relay of the compressor of the conditioner of air

85

Fuel pump and relay of the fuel pump

91

Injectors

92

Valve of management of idling air

93

Valve of a purge of a coal adsorber

94

Relay of the compressor of the conditioner of air

95