Citroen Xantia

since 1993 of release

Repair and car operation



Citroen Xantia
+ Introduction
+ Operation manual
+ Routine maintenance
- Engine repair
   + the Repair procedures which are not demanding extraction of the engine from the car - petrol engines
   - The repair procedures which are not demanding extraction of the engine from the car - diesel engines
      Measurement of kompressionny pressure and engine check on tightness
      Fixing cranked / distributive shaft and TNVD for the purpose of prevention of casual hit of valves in contact to pistons in the course of performance of procedures of service of the car
      Removal and installation of a cover of a head of cylinders
      Removal and installation of a pulley of a cranked shaft
      Removal and installation of covers of a gas-distributing belt
      Belt of a drive of GRM - the general information, removal, check of a condition and installation
      Removal and installation of cogwheels of a belt of a drive of GRM
      Removal and installation of components of the right support of the power unit and natyazhitel of a gas-distributing belt
      Removal and installation of an intermediate roller of a gas-distributing belt
      Removal, check of a condition and installation of a camshaft and pushers of valves
      Check and adjustment of klapanny gaps
      Removal and installation of a head of cylinders
      Removal and installation of the pallet of a case
      Removal, check of a condition and installation of the oil pump with a driving chain
      Replacement of epiploons
      Sensors of level, pressure and temperature of impellent oil - the general information
      Removal, check of a condition and flywheel installation / driving disk
      Check of a condition and replacement of support of a suspension bracket of the power unit
      Removal and installation of a maslookhladitel
   + Removal and major maintenance of the engine
+ Systems of cooling, heating
+ Power supply system and release
+ engine Electric equipment
+ Coupling
+ Transmission
+ Power shafts
+ Uniform hydraulic system
+ Brake system
+ Running gear and steering
+ Body and salon furnish
+ Onboard electric equipment
+ electric equipment Schemes


ad6e8668 ( )

Removal and installation of covers of a gas-distributing belt

Removal

Top forward cover (model of early years of release)

 PERFORMANCE ORDER

1. If dismantle of covers is made for the purpose of replacement of a gas-distributing belt, remove an arm of fastening of the right support of the power unit to a body (see. Removal and installation of components of the right support of the power unit and a natyazhitel of a gas-distributing belt) for the purpose of expansion of working space.
2. Release the top clamp of a cover.

3. Having hooked a screw-driver, liberate the bottom lock uvula, lift a cover up and remove it from the engine.

Top back cover (model of early years of release)

 PERFORMANCE ORDER

1. Remove the top forward cover (see above).

2. Release two clamps, uncover fixing hairpins on a forward wall of the engine and lift it up. The working space is extremely limited, therefore for the purpose of its expansion it will be reasonable to dismantle previously the carburetor of the corresponding support of the power unit (see. Removal and installation of components of the right support of the power unit and natyazhitel of a gas-distributing belt).

Top forward cover (model of the last years of release)

 PERFORMANCE ORDER

1. Give fixing the screw with a nut and uncover the engine.

Top back cover (model of the last years of release)

 PERFORMANCE ORDER

1. Remove a forward cover (see above), then turn out fixing bolts and remove a back cover.

Bottom cover (model of early years of release)

 PERFORMANCE ORDER

1. Remove a pulley of a cranked shaft (see. Removal and installation of a pulley of a cranked shaft).

2. Turn out two fixing bolts and remove the bottom cover of a gas-distributing belt from the engine.

Bottom cover (model of the last years of release)

 PERFORMANCE ORDER

1. Remove a pulley of a cranked shaft (see. Removal and installation of a pulley of a cranked shaft).
2. Remove both top covers (see above).
3. Give fixing nuts and bolts and remove the bottom cover.

Installation

Installation is made as it should be, the return to a dismantle order. Track correctness of placement of covers and reliability of a tightening of fixture (see. Specifications).