Citroen Xantia

since 1993 of release

Repair and car operation



Citroen Xantia
+ Introduction
+ Operation manual
+ Routine maintenance
+ engine Repair
+ Systems of cooling, heating
- Power supply system and release
   + the Power supply system - petrol models
   - Power supply system - diesel models
      Power supply system filling with fuel and removal from it air jams
      Check and adjustment of the maximum turns of the engine
      Removal, installation and adjustment of the thermosensitive sensor of turns of fast idling
      The electromagnetic locking valve - general information, removal and installation
      Removal and TNVD installation
      Methods of check of installation of the moments of injection of fuel
      Check and adjustment of the moments of injection (TNVD Lucas)
      Check and adjustment of the moments of injection (TNVD Bosch)
      Check of serviceability of functioning, removal and installation of nozzles of injection of fuel
      Removal, installation and adjustment of a cable of gas
      Removal and installation of a pedal of gas
      Removal and installation of assembly of a toplivozabornik with the fuel consumption sensor
      Removal and installation of a fuel tank
      Removal and installation of the inlet pipeline and final collector
      Turbokompressor - general information and precautionary measures
      Removal and turbokompressor installation
      Check of a condition and regenerative repair of a turbokompressor
      Removal and installation of the built-in cooler of a turbokompressor
      Removal and installation of an air purifier and accompanying components
   + Systems of decrease in toxicity and production of the fulfilled gases
+ engine Electric equipment
+ Coupling
+ Transmission
+ Power shafts
+ Uniform hydraulic system
+ Brake system
+ Running gear and steering
+ Body and salon furnish
+ Onboard electric equipment
+ electric equipment Schemes


ad6e8668

Check and adjustment of the maximum turns of the engine

The screw of adjustment of the maximum turns is sealed up at manufacturer. It is meant that need for performance of adjustments hardly will arise. It is not necessary to break a plombirovka before the termination of terms of warranty service of the car. In case of need adjustments their performance will need a tachometer. Alternative methods are described in Head Routine maintenance.


Adjusting points of TNVD of Lucas system

1 — the Lever manual останова the engine
2 — the Tube of return of fuel
3 — the Screw of adjustment of the maximum turns of the engine
4 — the Electromagnetic locking valve
5 — a fuel Admission

6 — the Cap of an opening of phases of a gazoraspredeleniye
7 — the Operating lever (the gas lever)
8 — the Screw of adjustment of turns of prevention spontaneous останова the engine
9 — the Lever of fast idling
10 — the Screw of adjustment of turns of idling


Adjusting points of TNVD of Bosch system

1 — the Screw of adjustment of turns of fast idling
2 — the Clamp of a tip of a cable
3 — the Lever of fast idling
4 — the Screw of adjustment of turns of idling
5 — the Screw of adjustment of turns of prevention spontaneous останова the engine

6 — the Screw of adjustment of a driving cable of fast idling
7 — the Screw of adjustment of a cable of gas
8 — the Screw of adjustment of the maximum turns of the engine
9 — the Operating lever (the gas lever)
and — the Adjusting washer of correction of turns of prevention spontaneous останова the engine


 PERFORMANCE ORDER

1. Start the engine and warm up it to normal working temperature.
2. Ask the assistant to squeeze out completely a gas pedal, and by means of a tachometer check the maximum turns of the engine on compliance to their requirements of Specifications. Do not allow operation of the engine on the maximum turns within more than two-three seconds.
3. In case of need, muffle the engine, remove a seal, weaken a lock-nut and by means of the adjusting screw (see illustrations Adjusting points of TNVD of Lucas system and Adjusting points of TNVD of Bosch system) execute correction of the maximum turns of the engine. Again strongly tighten a lock-nut.
4. For check of results of adjustment repeat the procedure described in the item 2.
5. Muffle the engine and disconnect a tachometer.