Citroen Xantia

since 1993 of release

Repair and car operation



Citroen Xantia
+ Introduction
+ Operation manual
+ Routine maintenance
+ engine Repair
+ Systems of cooling, heating
+ Power supply system and release
+ engine Electric equipment
+ Coupling
+ Transmission
+ Power shafts
+ Uniform hydraulic system
+ Brake system
- Running gear and steering
   Removal and installation of stupichny assembly of a forward suspension bracket
   Replacement of bearings of forward naves
   Removal, major maintenance and installation of the bottom lever of a forward suspension bracket
   Removal and installation of the bottom spherical support of a forward suspension bracket
   Removal and installation of components of the stabilizer of cross-section stability of a forward suspension bracket
   Removal and installation of assemblies of racks / hydraulic blocks of a forward suspension bracket
   Removal and installation of the proof-reader of height of a road gleam of a forward suspension bracket
   Removal and installation of a stretcher of a forward suspension bracket
   Removal and installation of naves of back wheels
   Replacement of back stupichny bearings
   Removal and installation of longitudinal levers of a back suspension bracket
   Removal and installation of assembly of the back bridge
   Removal and installation of hydraulic blocks of a back suspension bracket
   Removal and installation of the proof-reader of a road gleam of a back suspension bracket
   Check of installation and adjustment of a road gleam
   Removal and installation of a steering wheel
   Removal, check of a condition of components and installation of a steering column
   Removal and installation of assembly of the switch of the ignition/lock of a steering column
   The steering mechanism - general information, removal, major maintenance and installation
   System of hydrostrengthening of a wheel - general information
   Removal and installation of tips of steering drafts
   Corners of installation of wheels - the general information, check and adjustment of convergence of forward wheels
+ Body and salon furnish
+ Onboard electric equipment
+ electric equipment Schemes


ad6e8668

Removal and installation of hydraulic blocks of a back suspension bracket

For an otvorachivaniye from the hydraulic block of a spherical receiver the tape key is required. At installation of a receiver new sealing laying is required. Worn-out sealing elements of shtutserny sockets of hydraulic tubes also are subject to replacement.


Components of the hydraulic block of a back suspension bracket

And — the Tube of supply of hydraulic liquid
In — the Spherical receiver
With — the Spring clamp of fastening of a connecting bar of a suspension bracket
D — the Spring clamp of fastening of the hydraulic block


 PERFORMANCE ORDER

1. Dump pressure in hydraulic system (see. Head Uniform hydraulic system).
2. To Poddomkratta the car also establish it on props. Remove the corresponding back wheel.
3. Get under spuskny the gate of a regulator of pressure suitable drain capacity. By an otzhimaniye up the longitudinal lever of a suspension bracket extort from the hydraulic block the greatest possible amount of liquid.
4. By means of a tape key weaken landing of a spherical receiver, then turn out it from assembly of the hydraulic block.
5. Disconnect from the hydraulic block a tube of supply of liquid. At once закупорьте the open ends of a tube and the shtutserny socket in order to avoid hit in dirt system.
6. Remove a spring clamp from a connecting bar of a suspension bracket (see an illustration Components of the hydraulic block of a back suspension bracket).
7. Remove a spring clamp of fastening of the hydraulic block.
8. Remove the hydraulic block from assembly of the back bridge and disconnect from it returnable hydraulic and ventilating tubes.

Installation

 PERFORMANCE ORDER

1. Connect to the hydraulic block returnable and ventilating tubes and get assembly on the regular place. Track, that tubes did not appear are jammed.
2. Fix the hydraulic block a spring clamp.
3. Establish into place a clamp of a connecting bar of a suspension bracket.
4. Connect to the hydraulic block a tube of supply of liquid. At the corresponding complete set replace a sealing element of the shtutserny socket.
5. Grease a contact surface of a spherical receiver and establish it on the hydraulic block (do not forget to replace sealing laying).
6. Establish into place a wheel, then lower the car on the earth and tighten wheel bolts with demanded effort.
7. Tighten spuskny the gate of a hydraulic regulator of pressure and transfer a control lever a suspension bracket to the situation "Maximum".
8. Start the engine and examine all disconnected and acting in film components on existence of signs of leaks.
9. Check level of hydraulic liquid, in case of need make the corresponding adjustment (address to Head Routine maintenance).