Citroen Xantia

since 1993 of release

Repair and car operation



Citroen Xantia
+ Introduction
+ Operation manual
+ Routine maintenance
+ engine Repair
+ Systems of cooling, heating
+ Power supply system and release
+ engine Electric equipment
+ Coupling
+ Transmission
+ Power shafts
+ Uniform hydraulic system
+ Brake system
- Running gear and steering
   Removal and installation of stupichny assembly of a forward suspension bracket
   Replacement of bearings of forward naves
   Removal, major maintenance and installation of the bottom lever of a forward suspension bracket
   Removal and installation of the bottom spherical support of a forward suspension bracket
   Removal and installation of components of the stabilizer of cross-section stability of a forward suspension bracket
   Removal and installation of assemblies of racks / hydraulic blocks of a forward suspension bracket
   Removal and installation of the proof-reader of height of a road gleam of a forward suspension bracket
   Removal and installation of a stretcher of a forward suspension bracket
   Removal and installation of naves of back wheels
   Replacement of back stupichny bearings
   Removal and installation of longitudinal levers of a back suspension bracket
   Removal and installation of assembly of the back bridge
   Removal and installation of hydraulic blocks of a back suspension bracket
   Removal and installation of the proof-reader of a road gleam of a back suspension bracket
   Check of installation and adjustment of a road gleam
   Removal and installation of a steering wheel
   Removal, check of a condition of components and installation of a steering column
   Removal and installation of assembly of the switch of the ignition/lock of a steering column
   The steering mechanism - general information, removal, major maintenance and installation
   System of hydrostrengthening of a wheel - general information
   Removal and installation of tips of steering drafts
   Corners of installation of wheels - the general information, check and adjustment of convergence of forward wheels
+ Body and salon furnish
+ Onboard electric equipment
+ electric equipment Schemes


ad6e8668 https://glamorlady.ru:

Removal and installation of naves of back wheels

Removal

Do not remove a nave of back wheels without special need on that. Nave tightening from a pin of the back bridge will need a special stripper, and performance of this procedure is always connected with risk of damage of stupichny bearings. At assembly the new stupichny nut with a protective cap is required.


 PERFORMANCE ORDER

1. Remove a back brake disk (address to Head Brake system).

2. By means of a hammer and a big screw-driver with a flat sting accurately remove the central cap of protection of a stupichny nut (at assembly the cap is subject to replacement without fail).

3. By means of a hammer and a chisel расчеканьте a stupichny nut.

4. By means of a face natural a long collar weaken and unscrew a stupichny nut, then take a persistent washer.

At assembly the nut is subject to replacement without fail.

5. By means of a stripper pull together a nave from a pin of the back bridge assembled with an external holder of the stupichny bearing. Having removed a nave, use a stripper for removal from a pin of an internal holder of the bearing. Afterwards remove the remote plug (try to remember its adjusting situation).
6. Establish holders on the bearing and check freedom of its rotation. Originators of the real Management urgently recommend to make replacement of the stupichny bearing without fail in view of high degree of probability of damage of assembly in the course of nave dismantle. The last means need of replacement of all stupichny assembly as bearings in an individual order are not delivered.
7. Having removed a nave, estimate degree of wear of a pin of the back bridge, check it on existence of mechanical damages, in case of need make replacement. Assembly of a pin fastens on the bridge by means of a lock ring and can be brought down by means of a hammer with soft brisk, or is removed by means of a powerful stripper. At installation of a new nave track, that its shlitsa correctly entered into gearing with shlitsa of the longitudinal lever of a suspension bracket. Landing of a pin is carried out by means of a press, or an opravka suitable on the size and a hammer. Do not forget to replace a lock ring.

Installation

 PERFORMANCE ORDER

1. Grease a bridge pin with pure impellent oil, plant on it the remote plug, having tracked correctness of its placement.
2. Plant on a pin an internal holder of the new stupichny bearing, having begun to knock it a hammer through a tubular opravka.

Opravka should rest only against a flat face surface of a holder.

3. Check, whether the bearing is filled by greasing and plant stupichny assembly on a bridge pin. By means of a tubular opravka plant an external holder of the new bearing.
4. Establish a persistent washer, then screw a new stupichny nut, having tightened it with demanded effort. Reliably зачеканьте a nut, then plant a new protective cap.
5. Establish a brake disk (address to Head Brake system).