Citroen Xantia
+ Introduction
+ Operation manual
+ Routine maintenance
- Engine repair
- The repair procedures which are not demanding extraction of the engine from the car - petrol engines
Check of kompressionny pressure in cylinders
Fixing cranked / distributive shaft for the purpose of prevention casual in the course of performance of procedures of service of the car
Removal and installation of a cover of a head of cylinders
Removal and installation of a pulley of a cranked shaft
Removal and installation of covers of a gas-distributing belt
Belt of a drive of GRM - the general information, removal and installation
Removal, check of a condition and installation of a natyazhitel and cogwheels of a gas-distributing belt
Epiploon replacement (ов) camshaft
Removal, check of a condition and installation of a camshaft and pushers of valves
Check and adjustment of klapanny gaps
Removal and installation of a head of cylinders
Removal and installation of the pallet of a case of the engine
Removal, check of a condition and installation of the oil pump
Removal and installation of a maslookhladitel (model of 2.0 l)
Replacement of epiploons of a cranked shaft
Removal, check of a condition and flywheel installation / driving disk
Check of a condition and replacement of support of a suspension bracket of the power unit
+ the Repair procedures which are not demanding extraction of the engine from the car - diesel engines
+ Removal and major maintenance of the engine
+ Systems of cooling, heating
+ Power supply system and release
+ engine Electric equipment
+ Coupling
+ Transmission
+ Power shafts
+ Uniform hydraulic system
+ Brake system
+ Running gear and steering
+ Body and salon furnish
+ Onboard electric equipment
+ electric equipment Schemes
|
Replacement of epiploons of a cranked shaft
Right epiploon
|
|
|
1. Remove a cogwheel of a cranked shaft and (at the corresponding complete set) the remote plug (see. Removal, check of a condition and installation of a natyazhitel and cogwheels of a gas-distributing belt). Take a gas-distributing belt aside from a working zone and fix it there in order to avoid pollution by oil. Measure and write down adjusting depth of landing of an epiploon in the casing.
|
|
2. Puncture, or drill in a face surface of an epiploon pair of small openings and screw in them саморезы. Grasp heads of screws nippers and take an epiploon from the nest in a casing. Alternatively the epiploon can be taken by a poddevaniye way a screw-driver with a flat sting - try not to damage walls of a nest and a persistent coat hanger on a shaft pin. |
|
|
3. Clear a casing of an epiploon and carefully remove from walls of a nest and a shaft pin all roughnesses and the teases, capable to bring to failure of a new epiploon.
4. Grease sponges of a new epiploon with pure impellent oil, then accurately put on it a pin of a cranked shaft (sponges inside). Try not to damage soft sponges of an epiploon at putting on it on a pin.
5. By means of a suitable opravka (a face head of the corresponding size or a piece of a pipe of the corresponding diameter) begin to knock an epiploon in a casing nest on former depth (see item 1).
6. Collect rags excess of oil and establish into place a cogwheel of a cranked shaft (see. Removal, check of a condition and installation of a natyazhitel and cogwheels of a gas-distributing belt). |
|
Left epiploon
|
|
|
1. Remove a flywheel / a driving disk (see. Removal, check of a condition and flywheel installation / driving disk). Measure and write down adjusting depth of landing of an epiploon in the casing.
2. Puncture, or drill in a face surface of an epiploon pair of small openings and screw in them саморезы. Grasp heads of screws nippers and take an epiploon from the nest in a casing.
3. Clear a casing of an epiploon and carefully remove from walls of a nest and a shaft pin all roughnesses and the teases, capable to bring to failure of a new epiploon.
4. Grease sponges of a new epiploon with pure impellent oil, then accurately put on it a pin of a cranked shaft (sponges inside). Try not to damage soft sponges of an epiploon at putting on it on a pin.
5. By means of a suitable opravka (a face head of the corresponding size or a piece of a pipe of the corresponding diameter) begin to knock an epiploon in a casing nest on former depth (see item 1).
6. Collect rags excess of oil and establish into place a flywheel / a driving disk (see. Removal, check of a condition and flywheel installation / driving disk). |
|
|
|
