Citroen Xantia

since 1993 of release

Repair and car operation



Citroen Xantia
+ Introduction
+ Operation manual
+ Routine maintenance
+ engine Repair
+ Systems of cooling, heating
+ Power supply system and release
+ engine Electric equipment
+ Coupling
+ Transmission
+ Power shafts
+ Uniform hydraulic system
+ Brake system
+ Running gear and steering
- Body and salon furnish
   Care of components of a body and car bottom
   Care of an upholstery and salon carpets
   Repair of insignificant damages of body panels
   Repair of seriously damaged body panels
   Removal and installation of a front bumper
   Removal and installation of a rear bumper
   Removal, installation and cowl adjustment
   Removal and installation of a driving cable of an otpuskaniye of the lock of a cowl
   Removal and installation of locks of a cowl
   Removal, installation and adjustment of doors
   Removal and installation of panels of an internal upholstery of doors
   Removal and installation of door handles and lock components
   Removal and installation of regulators of window regulators of door windows
   Removal, installation and adjustment of a door of a back and its telescopic emphasis
   Removal and installation of components of the lock of a door of a back
   Removal and installation of components of the uniform lock
   Removal and installation of components of the electric drive of door window regulators
   Removal and installation of door rear-view mirrors and accompanying components
   Windscreen, glass of a door of a back and the other fixed glasses - the general information
   The top hatch - the general information
   External body furnish
   Removal and installation of seats
   Removal and installation of seat belts
   Removal and installation of elements of internal furnish of salon
   Removal and installation of the central console
   Removal and dashboard installation
   Control body sizes
+ Onboard electric equipment
+ electric equipment Schemes


ad6e8668

Removal and installation of panels of an internal upholstery of doors

Forward doors

Removal

 PERFORMANCE ORDER

1. Open a door and approximately on two thirds lower a windowpane. Disconnect a negative wire from the battery.

2. Extend the button of switching off of the lock, then by means of a small screw-driver wring out a lock uvula and finally remove the button.

3. On models with a manual drive of window regulators remove the management handle from the spindle, then remove a facing plate.

4. Turn out the screw located in the bottom back end of facing of the internal handle of a door.

5. Having accurately hooked, remove from the handle the facing panel. At the corresponding complete set, delay the panel of an internal upholstery from a doorframe and disunite contact sockets of electroconducting of a drive of a window regulator / a door rear-view mirror. If door mirrors are equipped with a manual drive, remove from the panel of an internal upholstery decorative furnish of the driving mechanism.

6. Turn out two bottom screws of fastening of an armrest.

7. Through an opening in the door handle turn out the top screw of fastening of an armrest (pay attention that the internal handle is a part of a design of an armrest).

8. Turn out the screw of fastening of the panel of the internal upholstery, located from the forward party of an opening of the internal handle.

9. Having accurately hooked a screw-driver, remove the panel of a cover of a loudspeaker.

10. Turn out three screws of fastening of the panel of the internal upholstery, located round the loudspeaker loudspeaker.

11. Hooking the suitable bifurcate tool, release the doors located on perimeter clamps and remove the panel of an internal upholstery (do not forget to disconnect electroconducting from a loudspeaker).

12. If there is a need for removal of the plastic sealing screen, it is necessary to dismantle previously the internal handle (see. Removal and installation of door handles and lock components) and, at the corresponding complete set, the control unit the window regulator electric drive:
   a) The control unit the electric drive of a window regulator fastens two screws used also for fixing of a block of contact sockets of electroconducting. Disconnect electroconducting, then turn out screws and remove the block;
   b) Liberate contact sockets from a block and remove the last;
   c) On the models equipped with the anticreeping alarm system, disunite the contact socket of electroconducting of the sensor of tracking (the sensor is built in in the decorative panel of furnish of a door mirror).

13. Accurately separate the sealing screen from a doorframe (if the screen is not replaced, try not to damage a film). At removal of the screen pass electroconducting plaits through openings through passage in it.

Installation

 PERFORMANCE ORDER

1. Installation is made upside-down. Pay attention to the next moments:
   a) Replace the panels of an internal upholstery damaged in the course of dismantle fixing clamps;

   b) Make sure, that the coupling screw of an executive rod of the door lock after installation of the internal handle was tightened;

   c) At installation of the button of switching off of the lock at first close a door and make sure that the executive rod of the switch is in the bottom situation. Translate a lock uvula in bottom of two openings, then densely plant the button for the rod end (before click), - the lock uvula thus should appear in the top opening.

Back doors

Removal

 PERFORMANCE ORDER

1. Disconnect a negative wire from the battery.
2. Open a door.
3. Execute the procedures described in subsection "Forward doors - Removal", subitem 2 — 11.
4. In need of removal of the plastic sealing screen at first release fastening clamps on a door of a basic arm of electroconducting.

Installation

See subsection "Forward doors - Installation".