Citroen Xantia

since 1993 of release

Repair and car operation



Citroen Xantia
+ Introduction
+ Operation manual
+ Routine maintenance
+ engine Repair
+ Systems of cooling, heating
+ Power supply system and release
+ engine Electric equipment
+ Coupling
+ Transmission
+ Power shafts
+ Uniform hydraulic system
+ Brake system
+ Running gear and steering
- Body and salon furnish
   Care of components of a body and car bottom
   Care of an upholstery and salon carpets
   Repair of insignificant damages of body panels
   Repair of seriously damaged body panels
   Removal and installation of a front bumper
   Removal and installation of a rear bumper
   Removal, installation and cowl adjustment
   Removal and installation of a driving cable of an otpuskaniye of the lock of a cowl
   Removal and installation of locks of a cowl
   Removal, installation and adjustment of doors
   Removal and installation of panels of an internal upholstery of doors
   Removal and installation of door handles and lock components
   Removal and installation of regulators of window regulators of door windows
   Removal, installation and adjustment of a door of a back and its telescopic emphasis
   Removal and installation of components of the lock of a door of a back
   Removal and installation of components of the uniform lock
   Removal and installation of components of the electric drive of door window regulators
   Removal and installation of door rear-view mirrors and accompanying components
   Windscreen, glass of a door of a back and the other fixed glasses - the general information
   The top hatch - the general information
   External body furnish
   Removal and installation of seats
   Removal and installation of seat belts
   Removal and installation of elements of internal furnish of salon
   Removal and installation of the central console
   Removal and dashboard installation
   Control body sizes
+ Onboard electric equipment
+ electric equipment Schemes


ad6e8668

Removal and installation of door rear-view mirrors and accompanying components

Mirrors with a manual drive

Removal

 PERFORMANCE ORDER

1. Remove the panel of an internal upholstery of a door (see. Removal and installation of panels of an internal upholstery of doors).
2. Separate and unbend the top forward corner of the plastic sealing screen of a door for the purpose of ensuring access to the plug of a driving cable of a regulator of situation of a mirror through passage. Take the plug from the door panel.
3. Having hooked, liberate from a door corner the panel of decorative furnish, at the corresponding complete set liberate from clamps on the panel the sensor of tracking of the anticreeping alarm system, then remove the panel.
4. Turn out five fixing screws and remove rear-view mirror assembly from a door. Pass a driving cable through an opening at doors. Try to remember a route of laying of a cable.

Installation

Installation is made upside-down. Track correctness of laying of a driving cable.

Mirrors with an electric drive

Removal

 PERFORMANCE ORDER

1. Remove the panel of an internal upholstery of a door (see. Removal and installation of panels of an internal upholstery of doors).

2. Find the ends of a spring clamp of fastening of the glass located from the upper edge of assembly of a mirror. Where it is required, remove the control unit the window regulator electric drive with a block of the contact socket for the purpose of ensuring access.

3. Take from the door panel the rubber plug of electroconducting through passage.

4. Having hooked, liberate from a door corner the panel of decorative furnish of knot of fastening of a mirror. At the corresponding complete set liberate from the panel the sensor of tracking of the anticreeping alarm system, then remove the panel.

5. Walk on an electroconducting plait from a mirror to a block and disunite contact sockets. At the corresponding complete set disconnect also electroconducting of the temperature sensor.

6. Turn out five fixing screws and remove mirror assembly from a door. Liberate from a door an electroconducting plait.





Installation

Installation is made upside-down. Track correctness of laying and reliability of fastening of electroconducting.

Mirror glass

Removal

 PERFORMANCE ORDER

1. Glass fastens in mirror assembly by means of a metal spring clamp.
2. Find the ends of a clamp of fastening of the glass located from the upper edge of assembly of a mirror. Where it is required, remove the control unit the window regulator electric drive with a block of the contact socket for the purpose of ensuring access.

3. Hook the clamp ends a screw-driver for the purpose of release of glass of a mirror.

4. Remove glass, at the corresponding complete set disconnect electroconducting. Remove from assembly a spring clamp if it is planted freely.
A — Contact sockets of electroconducting
B — the Spring clamp

Installation

 PERFORMANCE ORDER

1. Establish a spring clamp on the back party of glass of a mirror. Track, that the clamp ends correctly entered into glass grooves.
2. Fill glass in mirror assembly to a clamp zashchelkivaniye in an adjusting flute.

For simplification of landing of a clamp previously slightly grease a plastic ring on a regulator.

Switch of management of the electric drive of adjustment of provision of a door mirror

See. Head Onboard electric equipment.