Citroen Xantia

since 1993 of release

Repair and car operation



Citroen Xantia
+ Introduction
+ Operation manual
+ Routine maintenance
+ engine Repair
+ Systems of cooling, heating
+ Power supply system and release
+ engine Electric equipment
+ Coupling
+ Transmission
+ Power shafts
+ Uniform hydraulic system
+ Brake system
+ Running gear and steering
- Body and salon furnish
   Care of components of a body and car bottom
   Care of an upholstery and salon carpets
   Repair of insignificant damages of body panels
   Repair of seriously damaged body panels
   Removal and installation of a front bumper
   Removal and installation of a rear bumper
   Removal, installation and cowl adjustment
   Removal and installation of a driving cable of an otpuskaniye of the lock of a cowl
   Removal and installation of locks of a cowl
   Removal, installation and adjustment of doors
   Removal and installation of panels of an internal upholstery of doors
   Removal and installation of door handles and lock components
   Removal and installation of regulators of window regulators of door windows
   Removal, installation and adjustment of a door of a back and its telescopic emphasis
   Removal and installation of components of the lock of a door of a back
   Removal and installation of components of the uniform lock
   Removal and installation of components of the electric drive of door window regulators
   Removal and installation of door rear-view mirrors and accompanying components
   Windscreen, glass of a door of a back and the other fixed glasses - the general information
   The top hatch - the general information
   External body furnish
   Removal and installation of seats
   Removal and installation of seat belts
   Removal and installation of elements of internal furnish of salon
   Removal and installation of the central console
   Removal and dashboard installation
   Control body sizes
+ Onboard electric equipment
+ electric equipment Schemes


ad6e8668

Removal and installation of seats

Forward seats

On the models equipped with system of a pretightness of forward seat belts it is necessary to perform a small preparatory work:
   a) Take the ignition key;
   b) Disconnect a negative wire from the battery and wait about 10 minutes;
   c) Disunite the contact socket of electroconducting of the device of a pretightness (sockets are painted in orange color and are located under seats).

Do not undertake attempts of diagnosing of blocks of a pretightness of belts. Remember that giving of any power supply (including a current developed by the internal power supply of an ohmmeter) to natyazhitel leads to operation of their mechanisms. Besides, operation of natyazhitel occurs also at a warming up of assemblies to temperature above 100°С.


Rassoyedineniye of the contact socket of electroconducting of a natyazhitel of a forward seat belt

The seat is for descriptive reasons removed.

Removal

 PERFORMANCE ORDER

1. Accurately remove from external edge of a seat the plastic decorative panel. At first the panel should be delayed forward, then to shift towards a door for the purpose of liberation from clamps.

2. Turn out the bottom anchor bolt of fastening of a seat belt to a seat frame.

3. Shift a seat against the stop forward for the purpose of ensuring access to back fixing bolts. Turn out bolts.

4. Now shift a seat back and turn out forward bolts of its fastening.
5. On the models equipped with the electric drive of adjustment of the provision of seats before the beginning of dismantle it is necessary to make sure that the storage battery is disconnected.
6. At the corresponding complete set disunite the contact socket (ы) the electroconducting laid under a seat.
7. Remove a seat and take it from car salon.
8. Remove plastic floor boards (try to remember their adjusting situation).

Installation

Installation is made upside-down.

Pillow of a back seat (seat of a continuous design)

Removal

 PERFORMANCE ORDER

1. Lift a first line of a pillow and incline it forward.
2. Remove decorative covers from seat loops.
3. Give nuts of fastening of a pillow to loopy assemblies, then take a pillow from car salon.

Installation

Installation is made upside-down.

Back of a back seat (seat of a continuous design)

Removal

 PERFORMANCE ORDER

1. Release a clamp and combine a back forward.
2. Turn out screws of fastening of a back to the loopy assemblies located in the opposite ends of a seat. Lift a back and take it from car salon.

Installation

Installation is made upside-down.

Pillows of a back seat (seat of a separate design)

 PERFORMANCE ORDER

1. Execute subsection procedures "A pillow of a back seat (a seat of a continuous design) - Removal". For the purpose of ensuring access to nuts of fastening of loopy assemblies it is necessary to remove decorative covers from them.

Backs of a back seat (seat of separate type)

Removal

 PERFORMANCE ORDER

1. Release a clamp and combine a seat back forward.
2. Turn out fastening screws to a floor of the loopy assemblies located from both parties of a back of a seat. Pay attention that at removal of a back of a smaller seat it is enough to turn out fastening screws to a floor of only an external loop.
3. Lift a back and take it from car salon. At removal of a back of a smaller seat its internal edge should be liberated from a loopy level.

Installation

Installation is made upside-down.